Master Class

Master Class | October 7, 2016 | United States



Producing a quality weld on Inconel™

Master Class Department Header

Practical Advice on Welding with Inconel

The use of nickel alloy 625 (UNS N06625), commonly referred to as Inconel,™ is on the rise in the racing industry, specifically for the fabrication of high-performance exhaust systems. This nickel chromium-based alloy is sometimes identified under Aerospace Material Specifications.

There are a variety of different nickel-based alloys that fall under the Inconel name. They have all been extensively used in different industries because of their resistance to many types of severe corrosion and ability to withstand elevated temperature service.

Although nickel alloys are expensive and typically cost considerably more than stainless steel, the use of the 625 alloy is increasingly prevalent in the high budget motorsports industry because of its excellent high-temperature properties. This allows for much thinner wall thickness, which often reduces the weight of exhaust systems by half. Specialty exhaust system fabricators typically purchase the material in sheet form and use automated equipment to form and weld the tubes to the required diameter and thickness.

The wall thickness of nickel alloy exhaust components varies typically from 0.019 inch to 0.035 inch, but can run thicker for certain applications. Special heavy-duty mandrel benders are capable of making smooth tight radius bends. Shops specializing in this work sell the components to fabricators who build their own exhaust components and systems.

Thin-alloy 625 exhaust systems are usually joined by TIG (gas tungsten arc) welding. Aside from having a somewhat more sluggish or less fluid weld puddle, the alloy welds similarly to that of the 300 series of stainless steel. Both have low thermal conductivity and require less heat input to weld than carbon steel of the same thickness. Also, a nickel alloy tube, like stainless steel, needs to be purged with argon inside the tube (see our Master Class article on purging in the Fall 2015 issue of ARC Magazine for details).

A rule of thumb for optimum current settings for carbon steel is to use about 1 amp for every 0.001 inch of material thickness. When welding nickel alloy 625, as well as the 300 series of stainless steel, drop the amps by about 20% off of this rule. In general, try about 22 amps on 0.028-inch thickness material and adjust the current as needed with the remote.

One of the most important rules to successfully joining all nickel alloys is to thoroughly clean the base metal of all contaminants before welding or exposure to elevated temperatures. Some contaminants can lead to a loss of corrosion resistance and cracking in the welds or base metal. Sulphur, carbon, phosphorous, lead, zinc, copper and shop dirt are all known to cause problems. These contaminants can come from lubricants used in the secondary forming and cutting operations, marking crayons, paint sticks, ink, lay out dye, lead hammers, copper chill bars, etc. Fabricators should only use stainless steel wire brushes and abrasive disks that have not been in contact with iron or steel to clean nickel alloys.

Make sure to select the appropriate filler metal diameter to avoid excess amperage requirements needed to melt the thicker filler metal. A matching filler metal for joining alloy 625 is ER NiCrMo-3 (Techalloy® 625). It can be used to join 625 to stainless and carbon steel.

Avoid concave weld profiles and craters at the end of welds as they can be susceptible to hot cracking.

image
image
Master Class: Preheating Steel

Personal Protective Equipment

Heat-Resistant Welding Gloves
Safety Glasses
Welding Coat

Tools

Soapstone to mark area to be preheated

Temp stick to measure the temperature of the steel prior to welding

Oxy-propane torch (with striker)

image

PREHEAT SAFELY

We always want to make sure we’re working safely when welding and working with torches. Refer to ANSI Z49.1: “Safety in Welding, Cutting, and Allied Processes,” which includes heating.

Make sure to wear the proper safety gear, including flame-retardant clothing, gloves and proper safety glasses. Make sure your jeans or pants are not frayed.

For proper torch setup and application, refer to the manufacturer’s guidelines. Make sure to have the correct check valves on the torch, flash arresters back at the regulator, hoses in good condition, and regulators set and operating properly.