Project Spotlight

Project Spotlight | Wednesday, July 17, 2024 | United States



Enhance your property’s décor, as demonstrated by DIY guru Jimmy DiResta

Project Spotlight Department Header


SAFETY FIRST

Before you start any project involving welding, make sure you have the right Personal Protective Equipment (PPE), which includes, at least, an ANSI-approved welding helmet, safety glasses, appropriate welding gloves for the process you’re using, and a flame-resistant shirt, jacket, or sleeves to protect from UV rays and burns. You should also keep a fire extinguisher close at hand. Use adequate ventilation when welding. Use an approved respirator if exposure to welding fume cannot be controlled, or if welding outside and natural air movement is not sufficient to keep welding fume out of your breathing zone.


Building an Outdoor Bench

Nothing is more inviting than an outdoor bench. It says, “Come and sit. Relax. Forget about your cares for a minute or two.” It’s also where you can spend time on a beautiful morning with a cup of coffee or with a frosty beverage at the end of the day, relishing the peace and quiet of a night sky.

Constructing an outdoor bench with metal and wood is a relatively straightforward project for fabricators with basic skills and tools. Using your own choices for materials, any hobbyist can turn a simple design into a piece of furniture that will add to the décor and beauty of your property.

image

Step 1: Cut all of your frame pieces

Start by cutting all the pieces for the largest parts of the sub assembly — the seat and back frames — first. It’s important to make sure the two short pieces and two long pieces of the seat frame match each other so you can keep your bench seat perfectly square. To create the correct tilt on the seat back, cut one end of each piece at a 6-degree angle where it will meet the seat frame. A cross member will sit in the lower portion between the uprights to add support. It will be shorter than the top rail and cut square on each end.

image

Step 2: Weld up the seat frame

Tack weld the four pieces of the seat frame together. Check the diagonals and 90-degree angles to ensure that the frame is square. If the diagonals are off, a better fit can be had by gently persuading the frame with a dead-blow hammer or tapping the frame on the ground. Don’t wait until after the final weld to square up the frame. At that point, it’s too late. After you’ve ensured the frame is square, lay down your finish beads to bring the frame together and make it rigid. I like to grind my welds flat as I finish each subassembly, while I still have good access to the welds.

image

Step 3: Weld up the back frame

Using the seat frame as a guide, tack the two uprights and the top rail of the seat back frame together. Again, it is important to make sure that the back frame is level and square to the seat frame. At this point, you can set and tack weld your lower cross member into the seat back frame. While in the tack weld phase, continually check to make sure the frame doesn’t twist. It will be difficult to untwist the frame after you’ve done your finish welds. Lift the back frame to where you want it and tack weld it into place. One you’re satisfied with the placement of the back, proceed with your final welding and grinding (if needed).

image

Step 4: Front legs and armrests

Return to the chop saw to cut all the pieces for the legs and arm rests. Using clamps as needed, position the arm rests so they are parallel to the seat and perpendicular to the front legs. Once you’re confident everything is squared up, tack weld both pieces into place, followed by finish welds. Repeat this process on the opposite side.

image

Step 5: Weld the rear legs to the seat frame, scribe and cut

My rear legs are 2 inches shorter than the front legs, because I wanted to give people sitting on the bench the impression that they’re reclining. Tack the legs into place then finish weld. To get the best fit so the bench doesn’t rock or wobble, set the assembled frame into the space where it will ultimately live and scribe each leg to the ground. As you can see in the video (see link), I didn’t account for the slope of the sidewalk where the bench would go and had to use shims to compensate. Alternatively, you could use store-bought leveling feet.

image

Step 6: Support for the boards

Using pieces of ¾-inch wood as a guide, tack weld pieces of 1-inch-flat stock around the seat and back frames to act as supports for the seat and back slats. I used leftover wood from a prior job, so I bridged the short distance versus the longer one. If you decide to place your boards so they run parallel to the long side of the bench, you may need to add center supports. Drill holes into the flat stock and attach the slats with screws.

image

Step 7: Fill In the openings

To cap the open ends of the box tubing, I rubbed a profile of the bottom of the legs with paper and pencil to use as a template to cut out pieces of wood that will fit tightly into the openings. Once you’ve got a good fit, dab on a little two-part epoxy and tap them into place. You could also just as easily cut metal patches, weld them into place and grind them flush.

image

Step 8: Protect your work

If your bench is outside, you’ll want it to withstand the elements. Use teak oil to help protect the wood pieces. Lacquer will help slow down rust on the metal pieces, though it won’t eliminate it completely. If you’ve got deep pockets, you could build this out of stainless steel or even aluminum. A bench like that might even outlive you.

image
image
image
image
BUILDING AN OUTDOOR BENCH

Materials

4 feet of 2 x 4 16 ga. box tubing
30 feet of 2 x 2 16 ga. box tubing
16 feet of 1 inch 16 ga. flat stock
40 feet of 1 x 4 hardwood
¾-inch wood screws
Wipe-on polyurethane
Clear spray lacquer

WELDING/CUTTING EQUIPMENT
Lincoln Electric POWER MIG® 210 MP
Bandsaw with metal cutting blade
Bar clamps
Electric drill/driver
Angle grinder with abrasive disk

Welding/Cutting Equipment and Tools

Lincoln Electric POWER MIG® 210 MP
Bandsaw with metal cutting blade
Bar clamps
Electric drill/driver
Angle grinder with abrasive disk