A Trailer for Hauling Pallets

Project Spotlight | Wednesday, July 17, 2024 | United States



A practical summer fabrication project designed to move heavy palletized materials safely and efficiently.

Project Spotlight Department Header


SAFETY FIRST

Before you start any project involving welding, make sure you have the right Personal Protective Equipment (PPE), which includes, at least, an ANSI-approved welding helmet, safety glasses, appropriate welding gloves for the process you’re using, and a flame-resistant shirt, jacket, or sleeves to protect from UV rays and burns. You should also keep a fire extinguisher close at hand. Use adequate ventilation when welding. Use an approved respirator if exposure to welding fume cannot be controlled, or if welding outside and natural air movement is not sufficient to keep welding fume out of your breathing zone.


A SMALL TRAILER FOR HAULING PALLETS

For many of us, summer is the time when the landscaping and home improvement projects get into high gear. But when materials are delivered in large quantities on a wooden pallet, getting the goods from the end of the driveway to a place closer to the house or yard can be a challenge. In this issue, we build a small trailer that hitches to the back of your truck or car so you can haul the entire pallet to its destination without having to spend time and muscle on multiple trips. The trailer also includes a ramp that enables you to load and unload the goods without damage or mess. Here’s hoping your summer is fun and relaxing, and all of your projects are successful.

image

Step 1:

Use the pallet itself to create the template for the cart frame on the fabrication table. Use the band saw cutter to cut all the frame pieces square according to the template, then put a 45-degree bevel on each piece. You can cut wood templates to enable you to make quick and easy 45-degree angle cuts. Set up the frame pieces on the fabrication table, then grind away any rough edges to make each angle as smooth as possible. Use the Precision 225 TIG welder to weld the main frame together at each corner.

image

Step 2:

Using the POWER MIG® 215MP, weld the ribbing to the main frame of the deck to add strength and stability to the perimeter of the frame. This completes the main frame of the deck. Cut and weld the second deck in the same configuration as the first. The second deck will be the ramp that flips down. It will be identical to the main frame in size, shape and ribbing configuration.

image

Step 3:

Cut the expanded metal wire mesh with the angle grinder to fit the ramp. It will become the deck of the ramp, the deck of the underside of the ramp and the deck of actual working surface. Weld every open edge of the wire mesh to avoid any potential stability problems.

image

Step 4:

Use the plasma cutting software to map out the templates for the hinge plates and cut the ¼-inch plate. Grind the rough edges on each piece after cutting and bore a half-inch hole in each plate. Connect each set of plates with a nut and bolt, then weld the two hinge plate assemblies to the edges of the deck and ramp.

image

Step 5:

Pack the tire hubs with grease and bolt the axle/hub assembly to each tire. Cut the 2-inch x 2-inch square tubing to connect the two axles. If necessary, weld spacers onto the shaft of each axle to securely fit the axle into either end of the tubing. Weld the shafts into either end of the tubing. Cut the brace tubing with 45-degree bevels at both ends and weld them to the axle tube to secure the tube to the deck of the cart.

image

Step 6:

Cut the square tubing to make the two angled arms of the cart that will converge to connect to the hitch. Weld the angled arms to the cart, with a long tube at the center to become part of the ratchet mount. Square up the entire assembly with a laser before welding it all together.

image

Step 7:

Weld the ratchet crank to the side of the center tube and bolt the trailer hitch to the end of the tube. Weld a bolt onto a short strip of square tubing to mount the ratchet. Cut and weld the separate pieces to make the bracket, then weld the ratchet mount to the top of the bracket assembly.

image

Step 8:

Cut six 5-inch lengths of steel 2x4 to create the stake pockets for the outside of the trailer on three sides. Weld the pockets to the three sides using 2-inch angle iron as connecting pieces to keep the pockets slightly removed from the outer edges of the cart. Cut the wood panels and bolt them to the stakes to serve as liners for the sides of the trailer. Finish with a coat of paint to the deck, ramp and front assembly.

image
image
image
image

For more information about Jimmy Diresta:
YouTube  |  Website

image
A Small Trailer for Hauling Pallets

Materials

70 ft. of 1.5-square-in. 16-gauge tube
50 square ft. of expanded steel mesh
40 ft of 1x6-in. rough-cut wood for the side fence
36 3-in. carriage bolts
Trailer tires and hubs
Trailer hitch
Trailer adjustable leg
4 cans of green paint

Welding/Cutting Equipment and Tools

Horizontal band saw
Precision® 225 TIG welder
Power MIG® 215MP welder
Torchmate® 4400 cutting table