Shop Tricks and Tools

Shop Tricks and Tools | Wednesday, October 14, 2026 | United States



This practical fabrication tip explains how to properly back purge stainless tubing, resulting in cleaner weld roots, improved strength, and more professional results.

Shop Tricks & Tools Department Header

Back Purging Stainless Tube

We talked in a previous article about welding stainless steel and how and why to protect the back side of the weld from an effect known as “sugaring.” We showed how to protect stainless butt joints on the back side usng simple backing blocks that allow cover gas to protect the back of the weld.

An increasing number of hobbyists are welding an increasing amount of stainless, especially stainless tube, in their garages and shops. These projects might include car and motorcycle exhausts, hand railings furniture, and other items constructed from stainless tubing that require butt joints and full penetration welds. When sugaring occurs on the back side of the weld in tubular material, it can greatly affect the integrity of the weld. Back purging is a technique that can help ensure gas coverage to the back side or the root of your stainless tube welds.

Supplying cover gas to the back side of a weld can be done in several different ways. There are a variety of tools and equipment available, including paste flux, inserts, and inflatable dams that can be slid down the length of the tube or pipe and then blown up to block off the weld area and fill it with gas. Some of this equipment can be costly, and unless you are using it often, it can be cost prohibitive. But the method shown here is fast, easy and effective, and should be a part of all of your stainless butt welds.

For starters, you’ll need another gas line from another tank, or at the very least you’ll need a dual regulator that will feed two gas hoses. One hose will run into the machine as usual for the torch, and the other is just open and inserted into one end of the tube. This can be done with simple masking tape to seal off the hose feeding from one end. On the other end of the tube, tape off the opening and feed 3 to 5 CFH of cover gas into the inside of the tube. The last step is to poke several holes in the tape on the end opposite the feed hose.

The goal is a slow, low-volume flow of gas through the tube. If there are no exit holes in the end opposite the feed line, pressure will build in the tube, which will cause issues with the weld. Once the feed line is sealed and the opposite end with the exit holes is sealed, let the part sit for a minute to build enough gas inside. The next step is to make the first weld and move to the next one. Be careful not to weld too close to the tape, as the weld will easily melt the tape.

Even when you don't see sugaring on the inside of a stainless part, it doesn't mean that back purging is not an important step. Purging helps to maintain weld consistency and integrity. This can be especially important for parts that are subject to vibration, like motorcycle or automobile exhausts. Purged butt welds on parts like this help to ensure much higher quality all the way through the weld, which results in higher strength.

image
image
image
image
image

Square Tube Corners

Square tubing is one of the most common materials used in the making of tables, benches, trailers, or any other items that are constructed with 90-degree angles. When building these square-tube parts, leaving the ends open at the corners just isn’t the way to do things. Making the 90-degree angles at the corners can be done several different ways, including cutting two 45-degree angles at the end of each piece to form the necessary 90-degree angle. This method is employed frequently, but it requires the adjoining pieces to be held together correctly during the welding process. It is always best to tack all the pieces together before welding, but even then, it is difficult to keep the square in place.

One helpful technique is to cut the corners but not sever the material all the way through, leaving one side of the material uncut. This technique allows the corners to be held by themselves and does not require welding on the uncut side of the joint. Each time we weld, we add more heat to the piece, which usually results in more distortion. This technique, which requires the welding of only three sides of the tube rather than all four, is helpful in reducing distortion.

This technique can be employed one corner at a time, or you can carefully mark out and remove all the corners in a single step and then bend and weld each in succession. This will reduce the need for clamping parts in place, and it will also reduce distortion once the welding starts.

The first step is to measure exactly where you want the bend to happen and draw a straight line 90-degrees to the material. From the end of the perpendicular line, a 45-degree angle is cut on either side of the line. These 45-degree angles are cut and removed from the piece, but the material is not cut all the way through. The outer wall of the tube remains uncut and intact, which enables the tube to be bent to form the 90-degree corner.

Carefully use a saw or cut off wheel to cut and remove the three sides of the tube creating a V in the material but not all the way through. Once the material is removed, the two ends are bent together to form the perfect corner. All four corners can be laid out, marked and cut, and bent at the same time to form the square. Once the square is flat and true, tacking can begin, the tacks are placed on the inner corners on the top and the bottom. This will allow you to tune the square if needed. If it is out of alignment and swift hammer swing can easily true things up. Once the square is tacked and ready for welding, the first weld should be on the inside corner, move across the square for the next inside corner and so on. The flat sides of the tube should be the last joint to weld.

This fabrication technique, tacking sequence and welding sequence will help you construct flat, square and true frameworks. It will also reduce distortion during the welding process. It’s one of a few ways to create 90-degree angles from square material. If you’re careful in your measuring and cutting, it will make for proper right angles and sound fabrication work.

image
image
image
image
image
image
image