选项 关闭
10lb spool Pipeliner G70M
照片仅做参考，请以最终实物为准

直径 / 包装

直径
 10 lb 盘装
1.2 mm (0.047 in) ED033807

Pipeliner® 101M

气保护药芯焊丝电弧焊 | ED033807

等级:
E101T1-GM
E101T1-M21A4-K11

林肯电气Pipeliner® 101M药芯焊丝专为X80级管线钢热焊道、填充焊道及盖面焊道焊接设计

直径

选择直径

  • 1.2 mm (0.047 in)

包装

选择包装

  • 10 lb 盘装

详情

气体保护药芯焊丝，适用于最高X80级管线钢的热焊道、填充焊道及盖面焊道焊接

产品特性

  • 稳定电弧特性——专为自动化管道焊接工艺开发，确保关键工况下的恒定弧长控制
  • 平滑的焊道形貌——快凝型熔渣可提供全位置焊接的稳定熔池支撑
  • 冲击韧性——焊缝金属在-40℃(-40℉)下冲击功值可达27J
  • Q2 Lot® - 显示实际熔敷金属成分和力学性能的证书可在线获取
  • ProTech® 铝箔包装
  • Q2 Lot® - 显示每批次实际熔敷金属化学成分和力学性能的证书可在线获取
  • ProTech®包装 – 防潮型密封包装

服务支持

SDS信息 SDS 搜索页面

参考实验结果 免责声明

CONFORMANCE

CONFORMANCES SPECIFICATION CLASSIFICATION
AWS AWS A5.29 E101T1-GM
AWS AWS A5.36 E101T1-M21A4-K11

MECHANICAL PROPERTIES

Classification Shielding Gas Polarity Yield Strength @ 0.2% Offset
MPa (ksi) 		Tensile Strength
MPa (ksi) 		Elongation
% 		Charpy V-Notch
J (ft-lbs) @ -40°C (-40°F)
E101T1-GM Requirement 75-80% Ar, balance CO2 DC+ 610 (88) min. 690-830 (100-120) 16 min.
E101T1-M21A4-K11 Requirement M21-ArC DC+ 610 (88) min. 690-830 (100-120) 16 min. 27 (20) min.
Typical Result, As-welded 75% Ar, 25% CO2 DC+ 630 (92) 690-740 (100-107) 19 52-120 (38-88)

DEPOSIT COMPOSITION

Classification Shielding Gas Polarity %B %C %Cr %Mn %Mo %Ni %P %S %Si %V
E101T1-GM Requirement 75-80% Ar, balance CO2 DC+ Info. Only 0.30 min. * 0.50 min. * 0.20 min. * 0.50 min. * 0.030 max. 0.030 max. 1.00 max. 0.10 min. *
E101T1-M21A4-K11 Requirement M21-ArC DC+ 0.15 max. 0.20 max. 1.00 - 2.50 0.50 max. 0.40 - 1.00 0.030 max. 0.030 max. 0.80 max. 0.05 max.
Typical Result 75% Ar, 25% CO2 DC+ 0.004-0.0043 0.06-0.07 0.06 1.48-1.64 0.34-0.39 0.76-0.86 0.015 max. 0.010 max. 0.26-0.30 0.01

TYPICAL OPERATING PROCEDURES

Diameter Shielding Gas Polarity CTWD
mm (in.) 		Wire Feed Speed
m/min (in/min) 		Voltage
volts 		Approx. Current
amps 		Melt-off Rate
kg/hr (lb/hr)
1.2 mm (0.045 in) 75-80% Ar / balance CO2 DC+ 19 (3/4) 4.4-10.2 (175-400) 23-30 130-275 1.8-4.1 (3.9-9.0)

NOTES

Note
* To meet the requirements of a "G" classification, the chemical composition of the weld deposit must meet the minimum requirement for one or more of these elements.